The traceable 1.10ml storage vials from Micronic work equally well with either screw caps or push caps. The tubes have a net working volume of 0.80ml when used with screw cap or 0.90ml when used with push cap (working volume at +21°C). The 1.10ml tubes are standard available in the Roborack-96 or Micronic 96-3 Rack. The 1D barcoded racks are based on the ANSI/SLAS standards for storage racks and are produced in a certified class 7 clean room.
Micronic labware is manufactured and assembled in-house in a NEN-EN-ISO14644-1 Class 7 certified clean room environment (which is comparable to the US Federal Standard 209E Class 10,000).
For the manufacturing of its long term sample storage labware products Micronic uses solely virgin plastic raw material. The raw materials and auxiliary agents are selected based on the specifications that satisfy the high quality requirements of our products. The materials are FDA approved and comply with the (USA) USP XXII tests, including class VI (Medical approved), and the European Pharmacopoeia-monograph 3.2.2 unless communicated otherwise. Material components used to produce Micronic labware can be traced via the lot number indicated on the packaging.
The materials used for Micronic tubes are the result of extensive research. One selection criterion is that the amount of measurable extractables leaching into samples is minimized.
By maintaining the highest possible hygiene level during our production processes, Micronic manufactured labware is free of any detectable RNase or DNase contamination and the endotoxin level of produced and packaged labware is limited to an acceptable minimum (< 0.01 EU/ml). Our products are periodically tested on RNase, DNase and their endotoxin levels by independent expert organizations.
The Micronic 2D Data-Matrix codes and 1D barcodes are produced conform industry standards. The 2D Data-Matrix code (which adheres to the ECC200 standard) and 1D barcode (type 128B) are laser-etched into the code area and are guaranteed unique.
Products produced by Micronic are tested according to AQL inspection level G2 and AQL value 0.4.
Micronic Sample Storage tubes are classified as general laboratory products according to leading European Life Science Organizations (GAMBICA, FHI, LABMAS, Laborama, SPECTARIS). More information can be found here.
Upon request, Micronic products can be supplied gamma irradiated or ethylene oxide treated.
Our products comply with the IATA requirements for the transport of diagnostic specimens (UN packing instruction 602 and 650), assuming that our products are properly used (closed).
If you have any additional questions on the quality and safety of our products, please feel free to contact Micronic at sales@micronic.com.
Push Caps: The TPE Caps are availabe in several formats: the Capcluster-96 which leaves each tube individually capped, the Capmat-96 holds 96 caps in a fixed foil in which the tubes are sealed together, and the Capband-8 or -12 comes in a mat format with tear off lines to obtain cap strips.
Manual Decapping Tools: All manual decappers are compatible with the Micronic TPE Push Caps, TPE LyoCaps and EVA Push Caps in 96-well format of 0.50ml, 0.75ml, 1.10ml, 1.40ml, 2.00ml, and 2.50ml tubes. The Micronic Manual Decappers are cost effective solution for quick decapping.
Push Cap Capper CP400: Offers a cost effective way of applying uniform pressure to push caps in an entire 96 tubes rack in only a single action. The manual capper is able to repeatably and reliably securely cap tubes (up to 1.40ml) in all ANSI /SLAS format racks up to a maximum height of 48mm.
Push Cap Capper CP600/610: The Electric Capper CP600 can cap the following Micronic Push Caps on 96-format tubes (0.50ml, 0.75ml, 1.10ml, 1.40ml) in rack. The Electric Capper CP610 can cap Micronic Push Caps on 96-format tubes (up to 2.50ml) in rack. No adapters required.
| Parameter | 1.10ml Tubes Internal Thread |
|---|---|
| Inner tube shape | V-bottom |
| Material | Highest purity PP |
| Working volume (+21ºC) | 0.80ml (with Screw Cap) / 0.90ml (with Push Cap) |
| Tube height in rack | 39.0mm (without cover) |
| Resistance | Chemical solvents |
| Temperature range | Vapor phase LN2 to +100°C |
| Article Number | Description | Unit Size | Case Size |
|---|---|---|---|
| MP32033 | 1.10ml Non coded Screw Cap tubes with Internal Thread V-bottom Bulk | 960 tubes | 4 |
| MP32033L | 1.10ml Non coded Screw Cap tubes with Internal Thread V-bottom Snap Bulk | 960 tubes | 4 |
| MP32120 | 1.10ml Non coded Screw Cap tubes with Internal Thread V-bottom in Micronic 96-3 Rack with low cover (Barcoded A1-H1 side) | 10 racks | 4 |
| MP32121 | 1.10ml Non coded Screw Cap tubes with Internal Thread V-bottom in Micronic 96-3 Rack with high cover (Barcoded A1-H1 side) | 10 racks | 4 |
| MP32175 | 1.10ml Non coded Screw Cap tubes with Internal Thread V-bottom in Micronic EFC 96-3 Rack RM with cover (Barcoded A1-H1 side) | 10 racks | 4 |
| MP52318 | 1.10ml 2D Data-Matrix coded Screw Cap tubes with Internal Thread V-bottom Bulk | 960 tubes | 4 |
| MP52318L | 1.10ml 2D Data-Matrix coded Screw Cap tubes with Internal Thread V-bottom Snap Bulk | 960 tubes | 4 |
| MP52540 | 1.10ml 2D Data-Matrix coded Screw Cap tubes with Internal Thread V-bottom in Micronic 96-3 Rack with low cover (Barcoded A1-H1 side) | 10 racks | 4 |
| MP52541 | 1.10ml 2D Data-Matrix coded Screw Cap tubes with Internal Thread V-bottom in Micronic 96-3 Rack with high cover (Barcoded A1-H1 side) | 10 racks | 4 |
| MP52602 | 1.10ml 2D Data-Matrix coded Screw Cap tubes with Internal Thread V-bottom in Micronic EFC 96-3 Rack RM with cover (Barcoded A1-H1 side) | 10 racks | 4 |
| MP52602-Z20 | 1.10ml 2D Data-Matrix coded Screw Cap tubes with Internal Thread V-bottom precapped with Grey Screw Cap in Micronic EFC 96-3 Rack RM with cover (Barcoded A1-H1 side | 10 racks | 4 |
The Micronic TPE Capcluster is compatible with 96-well format tubes. The TPE Capcluster is available in Natural + 12 different colors, providing for visual color identification.
All manual decappers are compatible with the Micronic TPE Push Caps, TPE LyoCaps and EVA Push Caps in 96-well format of 0.50ml, 0.75ml, 1.10ml, 1.40ml, 2.00ml, and 2.50ml tubes.
The Micronic Push Cap Capper CP400 offers a cost effective way of applying uniform pressure to Push Caps in an entire 96 tubes rack in only a single action.
The Push Cap Capper CP600 & CP610 can cap Micronic Push Caps (i.e. Capclusters or Capmats) on 96-format tubes with internal thread in rack.